Windows CE Programming

LEDTimedCandle

I did a lot of research on battery powered LED candle lights circuits and code and was unable to find a time controlled LED candle light.

As I have some ATTiny13 left, I decided to use this little chip. As I want the LED to do a candle light for about 4hours and then stay of for another 20 hours, I need on timer and counter. Another timer/PWM is needed to immitate a candle flickering. But the ATTiny13 has only one timer. On the ATTiny13 you can either use the timer or PWM.

Fortunately the ATTiny has also a Watchdog timer that can be used to call an interrupt function. The watchdog runs with a separate 128kHz clock, independent from the CPU clock. The largest timeout is 8 seconds. So I need to count this 450 times to have one hour.

// watchdog interrupt
ISR (WDT_vect)
{
  sec8_counter++;

#ifdef USE_HEART_BEAT_LED  
  //flash heart beat LED
  digitalWrite(LED2, HIGH);
  delay(1);
  digitalWrite(LED2, LOW);
#endif
  
  if(sec8_counter>=HOUR_INTERVAL){
    sec8_counter=0;
    if(bLedIsOn==1){
      on_hours++;
      if(on_hours>=MAX_ON_HOURS){
        bLedIsOn=0; //switch to OFF mode
        off_hours=0;
      }
    }else{
      off_hours++;
      if(off_hours>=MAX_OFF_HOURS){
        bLedIsOn=1; //switch to ON mode
        on_hours=0;
      }
    }
  }
  wdt_reset();
}  // end of WDT_vect

The code makes the ATTiny13 sleep for another 8 seconds or light the LED. The ON phase is 4 hours and the sleep phase will be extended to 20 hours.

void loop ()
{
  //sleep 20 hours and work 4 hours
  noInterrupts();
  if(bLedIsOn==1){
    doCandle();
  }else{
    digitalWrite (LED, LOW); //ensure LED is OFF
   goToSleep ();
  }
  interrupts();
}  // end of loop

The sequence starts with the ON phase, when power is applied. In the ON phase I measure about 3mA and in the OFF phase the circuit needs 300µA.

The circuit is documented in the Arduino code file. Running the ATTiny13 at lower clock than 9.6MHz did not change the power usage. But I switched to the 1.2MHz internal clock and disabled BOD (auto power down for low power) to get a longer runtime with two or three AA batteries.

UPDATE 2019/03/10: The wdt calculation is wrong and I changed the 450 cycles for one hour to 388. See github README for full update. The main issue is that the ATTiny13 datasheet says 128kHz but means 131072Hz and not 128000Hz and the wdt oscilator never cycles that fast but more or less at around 113000Hz.

https://github.com/hjgode/LEDTimedCandle/tree/master

CREDITS to all that share their knowledge, especially:

https://github.com/MCUdude/MicroCore

http://forum.arduino.cc/index.php?topic=200590.0

https://electronics.stackexchange.com/questions/74840/use-avr-watchdog-like-normal-isr

http://www.ece.cmu.edu/~koopman/lfsr/index.html

U5, U3 U7 Cree LED light with 3000lm and 30W?

There are various cheap High Power LED motorcyle LED lights out there, all coming with different circuits but all with 3 Modes: High Beam, Low Beam and Strobe Light.

A friend baught some of these LED Lights and asked me to remove the Strobe and Low Beam. Unfortunately, non of the existing posts had the same circuit board inside. During my research and tests I blew one the pair. I hoped to get a known circuit driven Light by buying another pair with Devil Eye, a blue Angel LED circle which is specified with 12-80V.

Continue reading ‘Electronics: Modify Cree like Motorcycle LED Fog Projector Light’ »